Review of Oceanis 300

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The boat is equipped with 3 cabins, 6 berths, a galley, 170.0 liter fresh water capacity and toilet facility.

The Oceanis 300 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Wing keel

But be aware that even though a Wing Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.

The boat can enter even shallow marinas as the draft is just about 1.35 - 1.45 meter (4.43 - 4.73 ft) dependent on the load. See immersion rate below.

Oceanis 300 may be equipped with an inboard Volvo Penta 2002 diesel engine at 18 hp (13 kW). Calculated max speed is about 6.4 knots

The fuel tank has a capacity of 65.0 liters (17 US gallons, 14 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oceanis 300 is 2.21, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oceanis 300 is about 190 kg/cm, alternatively 1063 lbs/inch.
Meaning: if you load 190 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1063 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Oceanis 300 is 16.0.

What is L/B (Length Beam Ratio)?

The l/b ratio for Oceanis 300 is 2.83.

What is a Ballast Ratio?

The ballast ratio for Oceanis 300 is 33%.

What is Displacement Length Ratio?

The DL-ratio for Oceanis 300 is 131 which categorizes this boat among 'ultra light racers'.

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 21.07

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 30m² (322 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Oceanis 300 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.