YachtDatabase.com

Review of Luffe 40.04


Basic specs.

sail specifications
The Luffe 40.04 is a large sailboat designed by the Danish maritime architect Oluf Jørgensen.

Here we would have liked to show you nice photos of the Luffe 40.04.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Luffe 40.04 or similar boat for sale

Interior

The boat is equipped with 4+2 berths and 100.0 liter fresh water capacity.


Rig

The Luffe 40.04 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

Fin keel

The Luffe 40.04 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can only enter major marinas as the draft is about 2.08 - 2.18 meter (6.82 - 7.12 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Luffe 40.04 is 1.89, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Luffe 40.04 is about 246 kg/cm, alternatively 1377 lbs/inch.
Meaning: if you load 246 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1377 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Luffe 40.04 is 22.3.

Low High 18% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 18% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Luffe 40.04 is 3.53.

Wide Slim 73% 0 50 100
Compared with other similar sailboats it is slimmer than 73% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Luffe 40.04 is 40%.

Low High 54% 0 50 100
This ballast ratio shows a righting moment that is higher than 54% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Luffe 40.04 is 132 which categorizes this boat among 'ultra light racers'.

Heavy Light 90% 0 50 100
90% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 23.71


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 44m2 (473 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 12.0 m(39.4 feet)14 mm(0.55 inch)
Genoa sheet12.0 m(39.4 feet)14 mm(0.55 inch)
Mainsheet 30.0 m(98.4 feet)14 mm(0.55 inch)
Spinnaker sheet26.4 m(86.6 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Luffe 40.04 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References