Review of Hanse 630e
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Hanse 630e or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 800.0 liter fresh water capacity.
The Hanse 630e is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Hanse 630e has been built with different keel alternatives.
DaggerBoard aka Sword
The Hanse 630e is equipped with a daggerboard keel. A daggerboard is a lifting keel that can be lowered and raised, allowing the boat to enter shallow waters as well.
The boat can only enter major marinas as the draft is about 2.20 - 2.30 meter (7.22 - 7.52 ft) dependent on the load. See immersion rate below.
Fin keel
The Hanse 630e is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
Hanse 630e can only enter major marinas as the draft is about 2.95 - 3.05 meter (9.68 - 9.98 ft) dependent on the load. See immersion rate below.
The Hanse 630e has been equipped with different engine alternatives.
Alternative 1:
The boat may be equipped with an inboard Yanmar diesel engine at 110 hp (81 kW). Calculated max speed is about 8.1 knots
Alternative 2:
The boat may be equipped with an inboard Volvo Penta D3-110 diesel engine at 110 hp (81 kW). Calculated max speed is about 8.1 knots
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank, which is made of stainless steel, has a capacity of 600.0 liters (158 US gallons, 131 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Hanse 630e is 1.83, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
Hanse 630e holds a CE certification:
The boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 10.0 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Hanse 630e is about 595 kg/cm, alternatively 3336 lbs/inch.
Meaning: if you load 595 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 3336 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Hanse 630e is 3.65.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Hanse 630e with ISO 8666 reference sail is 24.2, with a 135% genua the SA/D is 28.0.
Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 112m2 (1205 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for fractional rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 65.1 m | (213.7 feet) | 14 mm | (0.55 inch) |
| Jib/genoa halyard | 65.1 m | (213.7 feet) | 14 mm | (0.55 inch) |
| Spinnaker halyard | 65.1 m | (213.7 feet) | 14 mm | (0.55 inch) |
| Jib sheet | 19.0 m | (62.3 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 19.0 m | (62.3 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 47.5 m | (155.8 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 41.8 m | (137.1 feet) | 16 mm | (5/8 inch) |
| Cunningham | 8.4 m | (27.4 feet) | 14 mm | (0.55 inch) |
| Kickingstrap | 16.7 m | (54.9 feet) | 14 mm | (0.55 inch) |
| Clew-outhaul | 16.7 m | (54.9 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Hanse 630e it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.