Review of Bavaria 35 Match

Basic specs.

The Bavaria 35 Match is a sailboat. The Bavaria 35 Match is built by the German yard Bavaria Yachtbau GmbH.

Here we would have liked to show you nice photos of the Bavaria 35 Match.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Bavaria 35 Match or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

Fin keel

The Bavaria 35 Match is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.01 - 2.11 meter (6.59 - 6.89 ft) dependent on the load. See immersion rate below.

Engine

The boat may be equipped with an inboard Volvo Penta MD2020 diesel engine at 19 hp (14 kW).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bavaria 35 Match is about 238 kg/cm, alternatively 1335 lbs/inch.
Meaning: if you load 238 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1335 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Bavaria 35 Match is 3.27.

Compared with other similar sailboats it is slimmer than 58% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Bavaria 35 Match is 33%.

This ballast ratio shows a righting moment that is higher than 15% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	10.8 m	(35.4 feet)	14 mm	(0.55 inch)
Genoa sheet	10.8 m	(35.4 feet)	14 mm	(0.55 inch)
Mainsheet	27.0 m	(88.5 feet)	14 mm	(0.55 inch)
Spinnaker sheet	23.7 m	(77.9 feet)	14 mm	(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Bavaria 35 Match it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.