YachtDatabase.com

Review of Clipper 68


Basic specs.

sail specifications
The Clipper 68 is a large sailboat designed by the French maritime architect Edward George Dubois in the mid 2000. Only a few boats have been produced.

Here we would have liked to show you nice photos of the Clipper 68.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Clipper 68 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 779.0 liter fresh water capacity.


Keel

Fin keel

The Clipper 68 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can only enter major marinas as the draft is about 3.00 - 3.10 meter (9.84 - 10.14 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Clipper 68 is 1.85, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 10.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Clipper 68 is about 671 kg/cm, alternatively 3758 lbs/inch.
Meaning: if you load 671 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 3758 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Clipper 68 is 3.61.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 20.10


Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 114m2 (1227 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 20.8 m(68.2 feet)16 mm(5/8 inch)
Genoa sheet20.8 m(68.2 feet)16 mm(5/8 inch)
Mainsheet 52.0 m(170.6 feet)16 mm(5/8 inch)
Spinnaker sheet45.8 m(150.1 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Clipper 68 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References