Review of Nauticat 44
Basic specs.
Looking for a new boat? Find a Nauticat 44 or similar boat for sale
The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.
The boat is equipped with 0 cabins, 4-10 berths, a galley, 800.0 liter fresh water capacity and toilet facility.
The boat has more than one rig.
One option is a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.
Full keel
The Nauticat 44 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.
Nauticat 44 can only enter major marinas as the draft is about 1.80 - 1.90 meter (5.91 - 6.21 ft) dependent on the load. See immersion rate below.
The Nauticat 44 has been equipped with different engine alternatives.
Alternative 1:
The boat may be equipped with an inboard Ford diesel engine at 130 hp (96 kW). The speed is 9.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 2:
The boat may be equipped with an inboard Ford diesel engine at 120 hp (89 kW). Calculated max speed is about 8.8 knots
The fuel tank, which is made of stainless steel, has a capacity of 1000.0 liters (264 US gallons, 219 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Nauticat 44 is 1.53, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Nauticat 44 is about 285 kg/cm, alternatively 1596 lbs/inch.
Meaning: if you load 285 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1596 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Nauticat 44 is 44.7.
What is L/B (Length Beam Ratio)?
The l/b ratio for Nauticat 44 is 3.59.
The ballast ratio for Nauticat 44 is 38%.
What is Displacement Length Ratio?
The DL-ratio for Nauticat 44 is 265 which categorizes this boat among 'light crusers & offshore racers'.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 47m2 (505 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Ketch rig | ||||
| Usage | Length | Diameter | ||
| Jib sheet | 13.3 m | (43.6 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.3 m | (43.6 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 33.2 m | (109.1 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.3 m | (96.0 feet) | 16 mm | (5/8 inch) |
| Ketch rig | ||||
| Usage | Length | Diameter | ||
| Jib sheet | 13.3 m | (43.6 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 13.3 m | (43.6 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 33.2 m | (109.1 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 29.3 m | (96.0 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Nauticat 44 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.