YachtDatabase.com

Review of Sovereign 32


Sovereign 32
Sovereign 32.

Basic specs.

sail specifications
The Sovereign 32 is a sailboat designed by the British maritime architect Ian L. Anderson in the early seventies. The Sovereign 32 is built by the British yard Sea Glass Ltd..

Looking for a new boat? Find a Sovereign 32 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The boat is equipped with 265.0 liter fresh water capacity.


Rig
Rig
Sovereign 32 with spinnaker.
Rig
Rig of Sovereign 32.

Keel
Keel
Keel of Sovereign 32.

Fin keel

The Sovereign 32 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.52 - 1.62 meter (4.99 - 5.29 ft) dependent on the load. See immersion rate below.


Engine

Sovereign 32 may be equipped with an inboard Thornycroft diesel engine at 35 hp (26 kW). Calculated max speed is about 5.8 knots

The fuel tank has a capacity of 114.0 liters (30 US gallons, 25 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sovereign 32 is 1.72, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sovereign 32 is about 163 kg/cm, alternatively 914 lbs/inch.
Meaning: if you load 163 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 914 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sovereign 32 is 36.0.

Low High 96% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 96% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sovereign 32 is 3.05.

Slim Wide 62% 0 50 100
Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Sovereign 32 is 45%.

Low High 69% 0 50 100
This ballast ratio shows a righting moment that is higher than 69% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sovereign 32 is 415 which categorizes this boat among 'heavy cruisers'.

Heavy Light 2% 0 50 100
2% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 14.30


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 27m2 (290 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 9.8 m(32.0 feet)12 mm(1/2 inch)
Genoa sheet9.8 m(32.0 feet)12 mm(1/2 inch)
Mainsheet 24.4 m(80.0 feet)12 mm(1/2 inch)
Spinnaker sheet21.5 m(70.4 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Sovereign 32 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References