Review of S2 9.2C

Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with a galley and 140.0 liter fresh water capacity.

The S2 9.2C is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

The S2 9.2C has been built with different keel alternatives.

Fin keel

One option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter even shallow marinas as the draft is just about 1.49 - 1.59 meter (4.89 - 5.19 ft) dependent on the load. See immersion rate below.

Fin keel

Another option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

S2 9.2C can enter even shallow marinas as the draft is just about 1.19 - 1.29 meter (3.90 - 4.20 ft) dependent on the load. See immersion rate below.

The S2 9.2C has been equipped with different engine alternatives.

Alternative 1:

The boat may be equipped with an inboard Yanmar 3GM30F diesel engine at 27 hp (20 kW). Calculated max speed is about 6.2 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

Note: The Yanmar 3GM30F was optional from 1983.

Alternative 2:

The boat may be equipped with an inboard Yanmar 2GM20F diesel engine at 18 hp (13 kW). Calculated max speed is about 5.0 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

Note: The Yanmar 2GM20F was standard from 1983.

Alternative 3:

S2 9.2C may be equipped with an inboard Yanmar 2GM diesel engine at 15 hp (11 kW). Max speed is 6.0 knots.

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

Note: The Yanmar 2GM version was installed from 1980.

Alternative 4:

The boat may be equipped with an inboard Universal Atomic 4 gasoline engine at 30 hp (22 kW). Calculated max speed is about 6.5 knots

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 110.0 liters (29 US gallons, 24 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for S2 9.2C is 1.93, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for S2 9.2C is about 160 kg/cm, alternatively 897 lbs/inch.
Meaning: if you load 160 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 897 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for S2 9.2C is 25.4.

What is L/B (Length Beam Ratio)?

The l/b ratio for S2 9.2C is 2.91.

What is a Ballast Ratio?

The ballast ratio for S2 9.2C is 41%.

What is Displacement Length Ratio?

The DL-ratio for S2 9.2C is 279 which categorizes this boat among 'medium weight cruisers'.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for S2 9.2C with ISO 8666 reference sail is 16.4, with a 135% genua the SA/D is 19.6.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 26m² (279 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for S2 9.2C it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.