YachtDatabase.com

Review of Mariner 39


Basic specs.

sail specifications
The Mariner 39 is a sailboat designed by the maritime architect Eric White together with Arthur Berry in the early eighties. The Mariner 39 is built by the American yard Mariner Yacht, New Hampshire.

Here we would have liked to show you nice photos of the Mariner 39.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Mariner 39 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Rig

The Mariner 39 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

Fin keel

The Mariner 39 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter most marinas as the draft is just about 1.68 - 1.78 meter (5.51 - 5.81 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Mariner 39 is 1.72, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Mariner 39 is about 225 kg/cm, alternatively 1262 lbs/inch.
Meaning: if you load 225 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1262 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Mariner 39 is 34.9.

Low High 79% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 79% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Mariner 39 is 3.32.

Wide Slim 54% 0 50 100
Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Mariner 39 is 33%.

Low High 18% 0 50 100
This ballast ratio shows a righting moment that is higher than 18% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Mariner 39 is 299 which categorizes this boat among 'medium weight cruisers'.

Heavy Light 31% 0 50 100
31% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Mariner 39 with ISO 8666 reference sail is 14.3, with a 135% genua the SA/D is 17.0.

Low High 18% 0 50 100
The SA/D ratio indicates that it is faster than 18% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 85% 0 50 100
The Mariner 39 has more rig than 85% of all similar sailboats, which indicates that the boat is significantly overrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 37m2 (398 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for masthead rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 31.0 m(101.8 feet)12 mm(1/2 inch)
Jib/genoa halyard31.0 m(101.8 feet)12 mm(1/2 inch)
Spinnaker halyard31.0 m(101.8 feet)12 mm(1/2 inch)
Jib sheet 11.8 m(38.7 feet)14 mm(0.55 inch)
Genoa sheet11.8 m(38.7 feet)14 mm(0.55 inch)
Mainsheet 29.5 m(96.9 feet)14 mm(0.55 inch)
Spinnaker sheet26.0 m(85.2 feet)14 mm(0.55 inch)
Cunningham4.6 m(15.0 feet)12 mm(1/2 inch)
Kickingstrap9.1 m(30.0 feet)12 mm(1/2 inch)
Clew-outhaul9.1 m(30.0 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Mariner 39 (Berry & White) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References