Both the hull and the deck is made of hand laid fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 2 cabins, 5 berths, a galley, 500.0 liter fresh water capacity and toilet facility.
The boat has more than one rig.
One option is a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Jutlandic 37 has been built with different keel alternatives.
Wing keel
But be aware that even though a Wing Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Jutlandic 37 can enter most marinas as the draft is just about 1.50 - 1.60 meter (4.92 - 5.22 ft) dependent on the load. See immersion rate below.
Fin keel
One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.
The boat may be equipped with an inboard Volvo Penta 2003 TS diesel engine at 43 hp (32 kW). The speed is 9.0 knots.
The transmission is a saildrive.
The fuel tank, which is made of stainless steel, has a capacity of 200.0 liters (52 US gallons, 43 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Jutlandic 37 is 1.81, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Jutlandic 37 is about 264 kg/cm, alternatively 1479 lbs/inch.
Meaning: if you load 264 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1479 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Jutlandic 37 is 26.5.
What is L/B (Length Beam Ratio)?
The l/b ratio for Jutlandic 37 is 3.21.
The ballast ratio for Jutlandic 37 is 36%.
What is Displacement Length Ratio?
The DL-ratio for Jutlandic 37 is 148 which categorizes this boat among 'ultra light racers'.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 42m2 (452 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Fractional rig | ||||
Usage | Length | Diameter | ||
Jib sheet | 11.3 m | (37.1 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 11.3 m | (37.1 feet) | 14 mm | (0.55 inch) |
Mainsheet | 28.3 m | (92.8 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 24.9 m | (81.6 feet) | 14 mm | (0.55 inch) |
Fractional rig | ||||
Usage | Length | Diameter | ||
Jib sheet | 11.3 m | (37.1 feet) | 14 mm | (0.55 inch) |
Genoa sheet | 11.3 m | (37.1 feet) | 14 mm | (0.55 inch) |
Mainsheet | 28.3 m | (92.8 feet) | 14 mm | (0.55 inch) |
Spinnaker sheet | 24.9 m | (81.6 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Jutlandic 37 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.