Review of Hilbre One Design

Basic specs.

The Hilbre One Design aka Hilbre OD is a small sailboat designed by the British maritime architect Alan Harold Buchanan in the late fifties. Less than 100 boats have been produced.

Here we would have liked to show you nice photos of the Hilbre One Design.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Hilbre One Design or similar boat for sale

Hull

The hull is made of wood.

Rig

The Hilbre One Design is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Keel

CentreBoard

The Hilbre One Design is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 0.48 - 0.58 meter (1.57 - 1.87 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hilbre One Design is 1.88, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hilbre One Design is about 72 kg/cm, alternatively 406 lbs/inch.
Meaning: if you load 72 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 406 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hilbre One Design is 3.34.

Compared with other similar sailboats it is slimmer than 98% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Hilbre One Design is 25%.

This ballast ratio shows a righting moment that is higher than 14% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	6.0 m	(19.8 feet)	8 mm	(5/16 inch)
Genoa sheet	6.0 m	(19.8 feet)	8 mm	(5/16 inch)
Mainsheet	15.0 m	(49.4 feet)	8 mm	(5/16 inch)
Spinnaker sheet	13.2 m	(43.5 feet)	8 mm	(5/16 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Hilbre One Design it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.