Review of X-382
Basic specs.
Looking for a new boat? Find a X-382 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a sandwich construction which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 3 cabins, 4 - 6 berths, a galley and toilet facility.
The X-382 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
Fin keel
The X-382 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The boat can only enter major marinas as the draft is about 2.00 - 2.10 meter (6.56 - 6.86 ft) dependent on the load. See immersion rate below.
X-382 may be equipped with an inboard diesel engine at 27 hp (20 kW).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for X-382 is 1.99, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for X-382 is about 283 kg/cm, alternatively 1585 lbs/inch.
Meaning: if you load 283 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1585 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for X-382 is 3.12.
The ballast ratio for X-382 is 43%.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for X-382 with ISO 8666 reference sail is 19.0, with a 135% genua the SA/D is 22.6.
Maintenance
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 34.8 m | (114.0 feet) | 12 mm | (1/2 inch) |
| Jib/genoa halyard | 34.8 m | (114.0 feet) | 12 mm | (1/2 inch) |
| Spinnaker halyard | 34.8 m | (114.0 feet) | 12 mm | (1/2 inch) |
| Jib sheet | 11.5 m | (37.7 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.5 m | (37.7 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 28.7 m | (94.2 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 25.3 m | (82.9 feet) | 14 mm | (0.55 inch) |
| Cunningham | 4.4 m | (14.4 feet) | 12 mm | (1/2 inch) |
| Kickingstrap | 8.8 m | (28.8 feet) | 12 mm | (1/2 inch) |
| Clew-outhaul | 8.8 m | (28.8 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for X-382 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.