Review of Taswell 43

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

The boat is equipped with 727.0 liter fresh water capacity.

Fin keel

The Taswell 43 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.

The boat can only enter major marinas as the draft is about 1.91 - 2.01 meter (6.27 - 6.57 ft) dependent on the load. See immersion rate below.

Taswell 43 may be equipped with an inboard Yanmar 4JH-HTE diesel engine at 55 hp (40 kW). Calculated max speed is about 7.0 knots

The fuel tank has a capacity of 326.0 liters (86 US gallons, 71 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Taswell 43 is 2.33, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Taswell 43 is about 396 kg/cm, alternatively 2222 lbs/inch.
Meaning: if you load 396 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2222 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Taswell 43 is 21.5.

What is L/B (Length Beam Ratio)?

The l/b ratio for Taswell 43 is 2.57.

What is a Ballast Ratio?

The ballast ratio for Taswell 43 is 41%.

What is Displacement Length Ratio?

The DL-ratio for Taswell 43 is 187 which categorizes this boat among 'light racers'.

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Taswell 43 with ISO 8666 reference sail is 16.8, with a 135% genua the SA/D is 20.0.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 61m² (656 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Taswell 43 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.