Review of Salona 33
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Salona 33 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The boat is equipped with 4+2 berths, a galley, 180.0 liter fresh water capacity and 42.0 liter waste water capacity.
The Salona 33 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
The Salona 33 has been built with different keel alternatives.
Fin keel
The Salona 33 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.
The boat can enter most marinas as the draft is just about 1.75 - 1.85 meter (5.74 - 6.04 ft) dependent on the load. See immersion rate below.
Fin keel
The Salona 33 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
Salona 33 can only enter major marinas as the draft is about 2.15 - 2.25 meter (7.05 - 7.35 ft) dependent on the load. See immersion rate below.
Fin keel
The Salona 33 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The boat can only enter major marinas as the draft is about 2.00 - 2.10 meter (6.56 - 6.86 ft) dependent on the load. See immersion rate below.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Salona 33 is 1.98, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
Salona 33 holds a CE certification:
The boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Salona 33 is about 202 kg/cm, alternatively 1136 lbs/inch.
Meaning: if you load 202 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1136 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Salona 33 is 22.5.
What is L/B (Length Beam Ratio)?
The l/b ratio for Salona 33 is 2.98.
What is Displacement Length Ratio?
The DL-ratio for Salona 33 is 186 which categorizes this boat among 'light racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Salona 33 with ISO 8666 reference sail is 19.3, with a 135% genua the SA/D is 22.4.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 35m2 (376 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for fractional rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 32.5 m | (106.8 feet) | 10 mm | (3/8 inch) |
| Jib/genoa halyard | 32.5 m | (106.8 feet) | 10 mm | (3/8 inch) |
| Spinnaker halyard | 32.5 m | (106.8 feet) | 10 mm | (3/8 inch) |
| Jib sheet | 10.0 m | (32.8 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 10.0 m | (32.8 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 25.0 m | (81.9 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 22.0 m | (72.1 feet) | 12 mm | (1/2 inch) |
| Cunningham | 4.8 m | (15.8 feet) | 10 mm | (3/8 inch) |
| Kickingstrap | 9.7 m | (31.7 feet) | 10 mm | (3/8 inch) |
| Clew-outhaul | 9.7 m | (31.7 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Salona 33 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.