YachtDatabase.com

Review of Oyster 56


Basic specs.

sail specifications
The Oyster 56 is a large sailboat designed by the British maritime architect Robert Humphreys in the mid nineties. The Oyster 56 is built by the British yard Oyster Marine Ltd..

Here we would have liked to show you nice photos of the Oyster 56.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Oyster 56 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 643.0 liter fresh water capacity.


Keel

Fin keel

The Oyster 56 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.39 - 2.49 meter (7.84 - 8.14 ft) dependent on the load. See immersion rate below.


Engine

Oyster 56 may be equipped with an inboard Yanmar 4LE-TE diesel engine at 110 hp (81 kW). Calculated max speed is about 7.1 knots

The fuel tank has a capacity of 719.0 liters (189 US gallons, 158 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oyster 56 is 1.68, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 9.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oyster 56 is about 478 kg/cm, alternatively 2678 lbs/inch.
Meaning: if you load 478 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2678 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oyster 56 is 3.54.

Slim Wide 58% 0 50 100
Compared with other similar sailboats it is more spacy than 58% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Oyster 56 is 30%.

Low High 27% 0 50 100
This ballast ratio shows a righting moment that is higher than 27% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Oyster 56 is 238 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 34% 0 50 100
34% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 15.26


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 79m2 (850 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 17.5 m(57.3 feet)16 mm(5/8 inch)
Genoa sheet17.5 m(57.3 feet)16 mm(5/8 inch)
Mainsheet 43.7 m(143.3 feet)16 mm(5/8 inch)
Spinnaker sheet38.4 m(126.1 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Oyster 56 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References