Review of Oceanis 311

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

The Oceanis 311 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

The Oceanis 311 has been built with different keel alternatives.

CentreBoard

The Oceanis 311 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.

The boat can enter even shallow marinas as the draft is just about 0.80 - 0.90 meter (2.62 - 2.92 ft) dependent on the load. See immersion rate below.

Unknown keel type

The boat can enter most marinas as the draft is just about 1.51 - 1.61 meter (4.95 - 5.25 ft) dependent on the load. See immersion rate below.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oceanis 311 is about 190 kg/cm, alternatively 1066 lbs/inch.
Meaning: if you load 190 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1066 lbs cargo on the boat it will sink 1 inch.

What is L/B (Length Beam Ratio)?

The l/b ratio for Oceanis 311 is 2.95.

Compared with other similar sailboats it is more spacy than 69% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

What is a Ballast Ratio?

The ballast ratio for Oceanis 311 is 37%.

This ballast ratio shows a righting moment that is higher than 31% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.

The Oceanis 311 has more rig than 54% of all similar sailboats, which indicates that the boat is slightly overrigged.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 36m² (387 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Oceanis 311 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.