YachtDatabase.com

Review of Islander Bahama 26


Basic specs.

sail specifications
The Islander Bahama 26 is a sailboat designed by the American maritime architect Robert H. Perry in the mid seventies. The Islander Bahama 26 is built by the American yard Islander Yachts.

Here we would have liked to show you nice photos of the Islander Bahama 26.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Islander Bahama 26 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Keel

Fin keel

The Islander Bahama 26 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter even shallow marinas as the draft is just about 1.19 - 1.29 meter (3.90 - 4.20 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Islander Bahama 26 is 2.27, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Islander Bahama 26 is about 135 kg/cm, alternatively 756 lbs/inch.
Meaning: if you load 135 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 756 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Islander Bahama 26 is 17.1.

Low High 34% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 34% of all similar sailboat designs. This comfort value is just below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Islander Bahama 26 is 2.60.

Slim Wide 93% 0 50 100
Compared with other similar sailboats it is more spacy than 93% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Islander Bahama 26 is 36%.

Low High 34% 0 50 100
This ballast ratio shows a righting moment that is higher than 34% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Islander Bahama 26 is 240 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 46% 0 50 100
46% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 21m2 (226 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 7.9 m(26.0 feet)10 mm(3/8 inch)
Genoa sheet 7.9 m(26.0 feet)10 mm(3/8 inch)
Mainsheet 19.8 m(65.0 feet)10 mm(3/8 inch)
Spinnaker sheet17.4 m(57.2 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Islander Bahama 26 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References