YachtDatabase.com

Review of Humphreys One Design 35


Basic specs.

sail specifications
The Humphreys One Design 35 aka Humphreys OD 35 is a sailboat designed by the British maritime architect Robert Humphreys in the mid nineties. The Humphreys One Design 35 is built by the British yard Bowman.

Here we would have liked to show you nice photos of the Humphreys One Design 35.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Humphreys One Design 35 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 151.0 liter fresh water capacity.


Keel

Fin keel

The Humphreys One Design 35 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.16 - 2.26 meter (7.09 - 7.39 ft) dependent on the load. See immersion rate below.


Engine

Humphreys One Design 35 may be equipped with an inboard Volvo Penta MD2020 diesel engine at 19 hp (14 kW). Calculated max speed is about 5.9 knots

The fuel tank has a capacity of 79.0 liters (20 US gallons, 17 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Humphreys One Design 35 is 2.12, indicating that this boat would not be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Humphreys One Design 35 is about 217 kg/cm, alternatively 1218 lbs/inch.
Meaning: if you load 217 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1218 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Humphreys One Design 35 is 18.1.

Low High 12% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 12% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Humphreys One Design 35 is 3.11.

Slim Wide 62% 0 50 100
Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Humphreys One Design 35 is 43%.

Low High 66% 0 50 100
This ballast ratio shows a righting moment that is higher than 66% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Humphreys One Design 35 is 140 which categorizes this boat among 'ultra light racers'.

Heavy Light 90% 0 50 100
90% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 40m2 (430 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 10.6 m(34.9 feet)14 mm(0.55 inch)
Genoa sheet 10.6 m(34.9 feet)14 mm(0.55 inch)
Mainsheet 26.6 m(87.2 feet)14 mm(0.55 inch)
Spinnaker sheet23.4 m(76.7 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Humphreys One Design 35 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References