YachtDatabase.com

Review of First 44.7


Basic specs.

sail specifications
The First 44.7 is a large sailboat designed by the American maritime architect bureau Farr Yacht Design, Ltd. in the early 2000.

Here we would have liked to show you nice photos of the First 44.7.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a First 44.7 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Rig

The First 44.7 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

Unknown keel type

The boat can only enter major marinas as the draft is about 1.94 - 2.04 meter (6.36 - 6.66 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for First 44.7 is about 355 kg/cm, alternatively 1988 lbs/inch.
Meaning: if you load 355 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1988 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for First 44.7 is 3.36.

Slim Wide 50% 0 50 100
Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.


Maintenance

Rig

Dimensions of sail for fractional rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 44.5 m(145.9 feet)14 mm(0.55 inch)
Jib/genoa halyard44.5 m(145.9 feet)14 mm(0.55 inch)
Spinnaker halyard44.5 m(145.9 feet)14 mm(0.55 inch)
Jib sheet 13.3 m(43.8 feet)16 mm(5/8 inch)
Genoa sheet13.3 m(43.8 feet)16 mm(5/8 inch)
Mainsheet 33.4 m(109.5 feet)16 mm(5/8 inch)
Spinnaker sheet29.4 m(96.4 feet)16 mm(5/8 inch)
Cunningham6.2 m(20.4 feet)14 mm(0.55 inch)
Kickingstrap12.5 m(40.9 feet)14 mm(0.55 inch)
Clew-outhaul12.5 m(40.9 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for First 44.7 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References