YachtDatabase.com

Review of Columbia River One Design


Basic specs.

sail specifications
The Columbia River One Design aka Columbia River OD is a sailboat designed by the maritime architect Joseph M. Dyer in the mid thirties. Only a few boats have been produced. The Columbia River One Design is built by the American yard Astoria Marine Construction Co..

Here we would have liked to show you nice photos of the Columbia River One Design.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Columbia River One Design or similar boat for sale

Hull

The hull is made of wood.


Interior

The boat is equipped with 76.0 liter fresh water capacity.


Rig

The Columbia River One Design is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

CentreBoard

The Columbia River One Design is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.

The boat can enter even shallow marinas as the draft is just about 0.71 - 0.81 meter (2.33 - 2.63 ft) dependent on the load. See immersion rate below.


Engine

Columbia River One Design may be equipped with an inboard Universal gasoline engine

The fuel tank has a capacity of 76.0 liters (20 US gallons, 16 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Columbia River One Design is 1.85, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Columbia River One Design is about 131 kg/cm, alternatively 738 lbs/inch.
Meaning: if you load 131 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 738 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Columbia River One Design is 23.5.

Low High 62% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 62% of all similar sailboat designs. This comfort value is just above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Columbia River One Design is 3.15.

Wide Slim 62% 0 50 100
Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Columbia River One Design is 14%.

Low High 1% 0 50 100
This ballast ratio shows a righting moment that is higher than 1% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Columbia River One Design is 225 which categorizes this boat among 'light crusers & offshore racers'.

Heavy Light 62% 0 50 100
62% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 15.04


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 23m2 (247 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 8.5 m(27.8 feet)10 mm(3/8 inch)
Genoa sheet8.5 m(27.8 feet)10 mm(3/8 inch)
Mainsheet 21.2 m(69.6 feet)10 mm(3/8 inch)
Spinnaker sheet18.7 m(61.2 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Columbia River One Design it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References