YachtDatabase.com

Review of Sydney 47 CR


Basic specs.

sail specifications
The Sydney 47 CR is a large sailboat designed by the Australian maritime architect bureau Murray; Burns & Dovell Pty. Ltd. in the mid 2000.

Here we would have liked to show you nice photos of the Sydney 47 CR.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sydney 47 CR or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 238.0 liter fresh water capacity.


Rig

The Sydney 47 CR is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.


Keel

Fin keel

The Sydney 47 CR is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can only enter major marinas as the draft is about 2.94 - 3.04 meter (9.65 - 9.95 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sydney 47 CR is 1.95, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sydney 47 CR is about 328 kg/cm, alternatively 1837 lbs/inch.
Meaning: if you load 328 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1837 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sydney 47 CR is 23.6.

Low High 15% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 15% of all similar sailboat designs. This is a comfort value significantly below average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sydney 47 CR is 3.53.

Wide Slim 62% 0 50 100
Compared with other similar sailboats it is slimmer than 62% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sydney 47 CR is 143 which categorizes this boat among 'ultra light racers'.

Heavy Light 85% 0 50 100
85% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Sydney 47 CR with ISO 8666 reference sail is 26.1, with a 135% genua the SA/D is 30.3.

Low High 100% 0 50 100
The SA/D ratio indicates that it is faster than 100% of all similar sailboat designs in light wind.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 63m2 (678 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail for fractional rig.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 47.5 m(156.0 feet)14 mm(0.55 inch)
Jib/genoa halyard47.5 m(156.0 feet)14 mm(0.55 inch)
Spinnaker halyard47.5 m(156.0 feet)14 mm(0.55 inch)
Jib sheet 14.3 m(46.8 feet)16 mm(5/8 inch)
Genoa sheet14.3 m(46.8 feet)16 mm(5/8 inch)
Mainsheet 35.7 m(117.0 feet)16 mm(5/8 inch)
Spinnaker sheet31.4 m(103.0 feet)16 mm(5/8 inch)
Cunningham6.5 m(21.3 feet)14 mm(0.55 inch)
Kickingstrap13.0 m(42.7 feet)14 mm(0.55 inch)
Clew-outhaul13.0 m(42.7 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Sydney 47 CR it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References