Review of Standfast 36
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Standfast 36 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
Full keel
The Standfast 36 is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The boat can only enter major marinas as the draft is about 2.06 - 2.16 meter (6.76 - 7.06 ft) dependent on the load.
The boat may be equipped with an inboard Perkins diesel engine
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.2 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
The ballast ratio for Standfast 36 is 41%.
What is Displacement Length Ratio?
The DL-ratio for Standfast 36 is 314 which categorizes this boat among 'medium weight cruisers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Standfast 36 with ISO 8666 reference sail is 15.2, with a 135% genua the SA/D is 18.4.
Maintenance
Dimensions of sail.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 34.1 m | (111.8 feet) | 12 mm | (1/2 inch) |
| Jib/genoa halyard | 34.1 m | (111.8 feet) | 12 mm | (1/2 inch) |
| Spinnaker halyard | 34.1 m | (111.8 feet) | 12 mm | (1/2 inch) |
| Jib sheet | 11.0 m | (36.0 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.0 m | (36.0 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 27.4 m | (90.0 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 24.1 m | (79.2 feet) | 14 mm | (0.55 inch) |
| Cunningham | 3.7 m | (12.0 feet) | 12 mm | (1/2 inch) |
| Kickingstrap | 7.3 m | (24.0 feet) | 12 mm | (1/2 inch) |
| Clew-outhaul | 7.3 m | (24.0 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Standfast 36 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.