Review of Princess 32 (Andersen)
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Princess 32 (Andersen) or similar boat for sale
Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 6 berths, a galley and toilet facility.
The Princess 32 (Andersen) is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The boat may be equipped with an inboard Albin O-22 gasoline engine at 12 hp (8 kW). Calculated max speed is about 4.1 knots
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Princess 32 (Andersen) is 1.66, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 6.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Princess 32 (Andersen) is about 135 kg/cm, alternatively 759 lbs/inch.
Meaning: if you load 135 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 759 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Princess 32 (Andersen) is 30.4.
What is L/B (Length Beam Ratio)?
The l/b ratio for Princess 32 (Andersen) is 3.61.
What is Displacement Length Ratio?
The DL-ratio for Princess 32 (Andersen) is 290 which categorizes this boat among 'medium weight cruisers'.
What is Relative Speed Performance?
The Relative Speed Performance for Princess 32 (Andersen) is 50
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 9.8 m | (32.0 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 9.8 m | (32.0 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 24.4 m | (80.0 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 21.5 m | (70.4 feet) | 12 mm | (1/2 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Princess 32 (Andersen) it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.