Review of Oyster 46 (Holman & Pye)
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find an Oyster 46 (Holman & Pye) or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 545.0 liter fresh water capacity.
The Oyster 46 (Holman & Pye) is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.
The boat may be equipped with an inboard Perkins M90 diesel engine at 81 hp (60 kW). Calculated max speed is about 7.4 knots
The fuel tank has a capacity of 454.0 liters (119 US gallons, 99 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Oyster 46 (Holman & Pye) is 1.77, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 8.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Oyster 46 (Holman & Pye) is about 345 kg/cm, alternatively 1932 lbs/inch.
Meaning: if you load 345 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1932 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Oyster 46 (Holman & Pye) is 35.1.
What is L/B (Length Beam Ratio)?
The l/b ratio for Oyster 46 (Holman & Pye) is 3.28.
What is Displacement Length Ratio?
The DL-ratio for Oyster 46 (Holman & Pye) is 230 which categorizes this boat among 'light crusers & offshore racers'.
SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 15.56
Maintenance
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 14.0 m | (46.0 feet) | 16 mm | (5/8 inch) |
| Genoa sheet | 14.0 m | (46.0 feet) | 16 mm | (5/8 inch) |
| Mainsheet | 35.0 m | (115.0 feet) | 16 mm | (5/8 inch) |
| Spinnaker sheet | 30.8 m | (101.2 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Oyster 46 (Holman & Pye) it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.