Review of OVNI 400

Basic specs.

The OVNI 400 is a large sailboat designed by the French maritime architect bureau Mortain & Mavrikios in the late 2010.

Here we would have liked to show you nice photos of the OVNI 400.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an OVNI 400 or similar boat for sale

Hull

The hull is made of aluminium. Aluminum is strong and forgiving. Where an impact on a fiberglass hull will result in major gelcoat damage and possible cracking, an aluminum hull will probably only have a scratch or a small bend. The only concern is electrolysis. Ensure that you have proper sacrificial anodes installed.

Interior

The boat is equipped with 2 cabins, 6 berths and 401.0 liter fresh water capacity.

Rig

The OVNI 400 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Keel

DaggerBoard aka Sword

The OVNI 400 is equipped with a daggerboard keel. A daggerboard is a lifting keel that can be lowered and raised, allowing the boat to enter shallow waters as well.

The boat can enter even shallow marinas as the draft is just about 0.98 - 1.08 meter (3.22 - 3.52 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for OVNI 400 is 1.96, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for OVNI 400 is about 337 kg/cm, alternatively 1888 lbs/inch.
Meaning: if you load 337 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1888 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for OVNI 400 is 28.0.

Comparing this ratio with similar sailboats show that it is more comfortable than 38% of all similar sailboat designs. This comfort value is just below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for OVNI 400 is 2.97.

Compared with other similar sailboats it is more spacy than 86% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for OVNI 400 is 35%.

This ballast ratio shows a righting moment that is higher than 27% of all similar sailboat designs. A righting moment (ability to resist heeling) just below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for OVNI 400 is 201 which categorizes this boat among 'light crusers & offshore racers'.

69% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for OVNI 400 with ISO 8666 reference sail is 16.4, with a 135% genua the SA/D is 19.4.

The SA/D ratio indicates that it is faster than 31% of all similar sailboat designs in light wind.

Over- / underrigged

The OVNI 400 has more rig than 14% of all similar sailboats, which indicates that the boat is significantly underrigged.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 63m² (678 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for fractional rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	38.2 m	(125.5 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	38.2 m	(125.5 feet)	12 mm	(1/2 inch)
Spinnaker halyard	38.2 m	(125.5 feet)	12 mm	(1/2 inch)
Jib sheet	12.9 m	(42.3 feet)	14 mm	(0.55 inch)
Genoa sheet	12.9 m	(42.3 feet)	14 mm	(0.55 inch)
Mainsheet	32.2 m	(105.8 feet)	14 mm	(0.55 inch)
Spinnaker sheet	28.4 m	(93.1 feet)	14 mm	(0.55 inch)
Cunningham	5.3 m	(17.5 feet)	12 mm	(1/2 inch)
Kickingstrap	10.7 m	(35.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	10.7 m	(35.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for OVNI 400 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.