Review of Malö 40 (Olsson)
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Malö 40 (Olsson) or similar boat for sale
Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The deck is a sandwich construction which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 2 cabins, 6 berths, a galley, 250.0 liter fresh water capacity and toilet facility.
The Malö 40 (Olsson) is built with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
Full keel
The Malö 40 (Olsson) is built with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated.
The boat can enter even shallow marinas as the draft is just about 1.35 - 1.45 meter (4.43 - 4.73 ft) dependent on the load. See immersion rate below.
Malö 40 (Olsson) may be equipped with an inboard Volvo Penta MD17C diesel engine at 35 hp (26 kW). The speed is 8.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank, which is made of stainless steel, has a capacity of 200.0 liters (52 US gallons, 43 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Malö 40 (Olsson) is 1.85, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Malö 40 (Olsson) is about 173 kg/cm, alternatively 972 lbs/inch.
Meaning: if you load 173 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 972 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Malö 40 (Olsson) is 25.0.
What is L/B (Length Beam Ratio)?
The l/b ratio for Malö 40 (Olsson) is 3.13.
The ballast ratio for Malö 40 (Olsson) is 43%.
What is Displacement Length Ratio?
The DL-ratio for Malö 40 (Olsson) is 208 which categorizes this boat among 'light crusers & offshore racers'.
What is SA/D (Sail Area Displacement ratio)?
The SA/D for Malö 40 (Olsson) with ISO 8666 reference sail is 13.0, with a 135% genua the SA/D is 15.4.
What is Relative Speed Performance?
The Relative Speed Performance for Malö 40 (Olsson) is 2
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 28m2 (301 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 24.6 m | (80.5 feet) | 10 mm | (3/8 inch) |
| Jib/genoa halyard | 24.6 m | (80.5 feet) | 10 mm | (3/8 inch) |
| Spinnaker halyard | 24.6 m | (80.5 feet) | 10 mm | (3/8 inch) |
| Jib sheet | 9.5 m | (31.3 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 9.5 m | (31.3 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 23.8 m | (78.2 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 21.0 m | (68.9 feet) | 12 mm | (1/2 inch) |
| Cunningham | 3.6 m | (12.0 feet) | 10 mm | (3/8 inch) |
| Kickingstrap | 7.3 m | (24.0 feet) | 10 mm | (3/8 inch) |
| Clew-outhaul | 7.3 m | (24.0 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Malö 40 (Olsson) it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.