Review of Larsen 25

The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The deck is a double deck which improves the indoor climate.

Floor plan of Larsen 25.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 2 cabins, 4-5 berths, a galley, 15.0 liter fresh water capacity and toilet facility.

Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.

Rig of Larsen 25.

The Larsen 25 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Fin keel

The Larsen 25 is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

Larsen 25 can enter even shallow marinas as the draft is just about 1.40 - 1.50 meter (4.59 - 4.89 ft) dependent on the load. See immersion rate below.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Larsen 25 is 2.11, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Larsen 25 is about 119 kg/cm, alternatively 666 lbs/inch.
Meaning: if you load 119 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 666 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Larsen 25 is 13.8.

What is L/B (Length Beam Ratio)?

The l/b ratio for Larsen 25 is 3.22.

What is a Ballast Ratio?

The ballast ratio for Larsen 25 is 48%.

What is Displacement Length Ratio?

The DL-ratio for Larsen 25 is 117 which categorizes this boat among 'ultra light racers'.

What is Relative Speed Performance?

The Relative Speed Performance for Larsen 25 is 92

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 21m² (226 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Larsen 25 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.