Review of Edel 6

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior of Edel 6 anno 1982. Bild taget 7/7 2003

The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with one cabin, 4 berths, a galley, 40.0 liter fresh water capacity and toilet facility.

Galley of Edel 6 anno 1982. Date of photo 7/7 2003

The Edel 6 is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.

Fin keel

The Edel 6 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can enter even shallow marinas as the draft is just about 1.00 - 1.10 meter (3.28 - 3.58 ft) dependent on the load. See immersion rate below.

An outboard motor is often used on this boat. In that case Edel 6 will typically require a power of 2 - 3 hp, alternatively 48 - 58 lbs thrust if you prefer an electrical motor. Electric outboards are becoming popular for sailboat owners who want clean instant power with less noise and no exhaust fumes.

What is Capsize Screening Formula (CSF)?

The capsize screening value for Edel 6 is 2.45, indicating that this boat would not be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 5.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Edel 6 is about 92 kg/cm, alternatively 520 lbs/inch.
Meaning: if you load 92 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 520 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Edel 6 is 11.6.

What is L/B (Length Beam Ratio)?

The l/b ratio for Edel 6 is 2.66.

What is a Ballast Ratio?

The ballast ratio for Edel 6 is 37%.

What is Displacement Length Ratio?

The DL-ratio for Edel 6 is 177 which categorizes this boat among 'light racers'.

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 20.64

What is Relative Speed Performance?

The Relative Speed Performance for Edel 6 is 50

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 15m² (161 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Edel 6 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.