YachtDatabase.com

Review of Clipper 48 Ketch


Basic specs.

sail specifications
The Clipper 48 Ketch is a large sailboat designed by the maritime architect Alfred Edward Luders in the late seventies. The Clipper 48 Ketch is built by the Chinese yard Cheoy Lee Shipyard Ltd..

Here we would have liked to show you nice photos of the Clipper 48 Ketch.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Clipper 48 Ketch or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 757.0 liter fresh water capacity.


Rig

The Clipper 48 Ketch is equipped with a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.


Keel

Full keel

The Clipper 48 Ketch is equipped with a long keel. A full keel provide a better directional stability than a similar boat with a fin keel; on the other hand, better directional stability means also that the boat is more difficult to handle in a harbour with less space.

The boat can only enter major marinas as the draft is about 1.83 - 1.93 meter (6.00 - 6.30 ft) dependent on the load. See immersion rate below.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Clipper 48 Ketch is 1.65, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Clipper 48 Ketch is about 274 kg/cm, alternatively 1539 lbs/inch.
Meaning: if you load 274 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1539 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Clipper 48 Ketch is 40.9.

Low High 76% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 76% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Clipper 48 Ketch is 3.69.

Wide Slim 76% 0 50 100
Compared with other similar sailboats it is slimmer than 76% of all other designs. It seems that the designer has chosen a significantly more speedy hull design.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Clipper 48 Ketch is 352 which categorizes this boat among 'heavy cruisers'.

Heavy Light 10% 0 50 100
10% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 19.16


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 45m2 (484 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 14.6 m(47.9 feet)16 mm(5/8 inch)
Genoa sheet14.6 m(47.9 feet)16 mm(5/8 inch)
Mainsheet 36.5 m(119.8 feet)16 mm(5/8 inch)
Spinnaker sheet32.1 m(105.5 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Clipper 48 Ketch it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References