Review of Buzzards Bay 30

Basic specs.

The Buzzards Bay 30 is a large sailboat designed by the American maritime architect Nathanael Greene Herreshoff in the first decade of 1900. Only a few boats have been produced. The Buzzards Bay 30 is built by the American yard Herreshoff Manufacturing Co..

Here we would have liked to show you nice photos of the Buzzards Bay 30.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Buzzards Bay 30 or similar boat for sale

Hull

The hull is made of wood.

Keel

CentreBoard

The Buzzards Bay 30 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 0.91 - 1.01 meter (2.99 - 3.29 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Buzzards Bay 30 is about 202 kg/cm, alternatively 1131 lbs/inch.
Meaning: if you load 202 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1131 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Buzzards Bay 30 is 4.34.

Compared with other similar sailboats it is slimmer than 100% of all other designs. It seems that the designer has chosen a significantly more speedy hull design. This type of design is also referred to as 'needle'.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 34m² (365 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	14.3 m	(47.0 feet)	16 mm	(5/8 inch)
Genoa sheet	14.3 m	(47.0 feet)	16 mm	(5/8 inch)
Mainsheet	35.8 m	(117.5 feet)	16 mm	(5/8 inch)
Spinnaker sheet	31.5 m	(103.4 feet)	16 mm	(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Buzzards Bay 30 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.