YachtDatabase.com

Review of Bristol 43.3


Basic specs.

sail specifications
The Bristol 43.3 is a large sailboat designed by the American maritime architect Ted Hood together with Dieter Empacher from Germany in the mid eighties. The Bristol 43.3 is built by the American yard Bristol Yachts Inc..

Here we would have liked to show you nice photos of the Bristol 43.3.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Bristol 43.3 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 606.0 liter fresh water capacity.


Keel

CentreBoard

The Bristol 43.3 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 1.49 - 1.59 meter (4.89 - 5.19 ft) dependent on the load. See immersion rate below.


Engine

Bristol 43.3 may be equipped with an inboard Westerbeke diesel engine

The fuel tank has a capacity of 454.0 liters (119 US gallons, 99 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Bristol 43.3 is 1.73, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bristol 43.3 is about 268 kg/cm, alternatively 1501 lbs/inch.
Meaning: if you load 268 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1501 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Bristol 43.3 is 37.1.

Low High 79% 0 50 100
Comparing this ratio with similar sailboats show that it is more comfortable than 79% of all similar sailboat designs. This is a comfort value significantly above average.


L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Bristol 43.3 is 3.35.

Slim Wide 50% 0 50 100
Compared with other similar sailboats it is more spacy than 50% of all other designs. It seems that the designer has chosen an average hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Bristol 43.3 is 40%.

Low High 62% 0 50 100
This ballast ratio shows a righting moment that is higher than 62% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Bristol 43.3 is 319 which categorizes this boat among 'medium weight cruisers'.

Heavy Light 15% 0 50 100
15% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.


SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Bristol 43.3 with ISO 8666 reference sail is 15.2, with a 135% genua the SA/D is 18.0.

Low High 10% 0 50 100
The SA/D ratio indicates that it is faster than 10% of all similar sailboat designs in light wind.


Over- / underrigged

Low High 4% 0 50 100
The Bristol 43.3 has more rig than 4% of all similar sailboats, which indicates that the boat is significantly underrigged.


Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 55m2 (592 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

Dimensions of sail.

mainsail specifications headsail specifications

Are your sails worn out? You might find your next sail here: Sails for Sale



If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Mainsail halyard 36.7 m(120.5 feet)14 mm(0.55 inch)
Jib/genoa halyard36.7 m(120.5 feet)14 mm(0.55 inch)
Spinnaker halyard36.7 m(120.5 feet)14 mm(0.55 inch)
Jib sheet 13.2 m(43.2 feet)16 mm(5/8 inch)
Genoa sheet13.2 m(43.2 feet)16 mm(5/8 inch)
Mainsheet 33.0 m(108.1 feet)16 mm(5/8 inch)
Spinnaker sheet29.0 m(95.1 feet)16 mm(5/8 inch)
Cunningham5.1 m(16.8 feet)14 mm(0.55 inch)
Kickingstrap10.2 m(33.6 feet)14 mm(0.55 inch)
Clew-outhaul10.2 m(33.6 feet)14 mm(0.55 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Bristol 43.3 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References