Review of Brewer 12.8

Basic specs.

The Brewer 12.8 is a large sailboat designed by the Canadian maritime architect Edward S. Brewer in the early eighties. Only a few boats have been produced.

Here we would have liked to show you nice photos of the Brewer 12.8.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Brewer 12.8 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 757.0 liter fresh water capacity.

Keel

CentreBoard

The Brewer 12.8 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Brewer 12.8 is 1.87, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Brewer 12.8 is about 282 kg/cm, alternatively 1583 lbs/inch.
Meaning: if you load 282 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1583 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Brewer 12.8 is 31.6.

Comparing this ratio with similar sailboats show that it is more comfortable than 58% of all similar sailboat designs. This comfort value is just above average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Brewer 12.8 is 3.11.

Compared with other similar sailboats it is more spacy than 73% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Brewer 12.8 is 278 which categorizes this boat among 'medium weight cruisers'.

34% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Brewer 12.8 with ISO 8666 reference sail is 17.1, with a 135% genua the SA/D is 20.5.

The SA/D ratio indicates that it is faster than 42% of all similar sailboat designs in light wind.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 53m² (570 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	36.9 m	(121.2 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	36.9 m	(121.2 feet)	12 mm	(1/2 inch)
Spinnaker halyard	36.9 m	(121.2 feet)	12 mm	(1/2 inch)
Jib sheet	12.8 m	(42.0 feet)	14 mm	(0.55 inch)
Genoa sheet	12.8 m	(42.0 feet)	14 mm	(0.55 inch)
Mainsheet	32.0 m	(105.0 feet)	14 mm	(0.55 inch)
Spinnaker sheet	28.2 m	(92.4 feet)	14 mm	(0.55 inch)
Cunningham	5.0 m	(16.5 feet)	12 mm	(1/2 inch)
Kickingstrap	10.1 m	(33.0 feet)	12 mm	(1/2 inch)
Clew-outhaul	10.1 m	(33.0 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Brewer 12.8 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.