Review of Bowman 40 (Paine)

Basic specs.

The Bowman 40 (Paine) also known as Bowman 40 is a large sailboat designed by the maritime architect Chuck W. Paine in the late eighties. The Bowman 40 (Paine) is built by the British yard Southern Boatbuilding Co. Ltd..

Here we would have liked to show you nice photos of the Bowman 40 (Paine).
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Bowman 40 (Paine) or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 454.0 liter fresh water capacity.

Rig

Rig of Bowman 40 (Paine) anno 1995. Eliana. Bowman 40 Mk 2.

Keel

Unknown keel type

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.50 - 1.60 meter (4.92 - 5.22 ft) dependent on the load. See immersion rate below.

Engine

Bowman 40 (Paine) may be equipped with an inboard Perkins Prima M50 diesel engine at 50 hp (37 kW). Calculated max speed is about 6.8 knots

The fuel tank has a capacity of 265.0 liters (70 US gallons, 58 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Bowman 40 (Paine) is 1.88, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bowman 40 (Paine) is about 250 kg/cm, alternatively 1401 lbs/inch.
Meaning: if you load 250 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1401 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Bowman 40 (Paine) is 29.1.

Comparing this ratio with similar sailboats show that it is more comfortable than 50% of all similar sailboat designs. This is an average comfort value!

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Bowman 40 (Paine) is 3.18.

Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Bowman 40 (Paine) is 259 which categorizes this boat among 'light crusers & offshore racers'.

46% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Bowman 40 (Paine) with ISO 8666 reference sail is 16.7, with a 135% genua the SA/D is 19.9.

The SA/D ratio indicates that it is faster than 42% of all similar sailboat designs in light wind.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 39m² (419 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	36.0 m	(118.0 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	36.0 m	(118.0 feet)	12 mm	(1/2 inch)
Spinnaker halyard	36.0 m	(118.0 feet)	12 mm	(1/2 inch)
Jib sheet	12.2 m	(39.9 feet)	14 mm	(0.55 inch)
Genoa sheet	12.2 m	(39.9 feet)	14 mm	(0.55 inch)
Mainsheet	30.4 m	(99.8 feet)	14 mm	(0.55 inch)
Spinnaker sheet	26.8 m	(87.8 feet)	14 mm	(0.55 inch)
Cunningham	4.5 m	(14.8 feet)	12 mm	(1/2 inch)
Kickingstrap	9.0 m	(29.5 feet)	12 mm	(1/2 inch)
Clew-outhaul	9.0 m	(29.5 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Bowman 40 (Paine) it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.