Review of Wasa 530

The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.

Floor plan of Wasa 530.

Interior of Wasa 530.

The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 10 berths, a galley, 400.0 liter fresh water capacity and toilet facility.

Galley of Wasa 530.

Bathroom of Wasa 530.

Rig of Wasa 530.

The Wasa 530 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Unknown keel type

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.60 - 2.70 meter (8.53 - 8.83 ft) dependent on the load. See immersion rate below.

Wasa 530 may be equipped with an inboard Volvo Penta TMD 31 Turbo diesel engine at 98 hp (73 kW). Calculated max speed is about 8.4 knots

The fuel tank, which is made of stainless steel, has a capacity of 340.0 liters (89 US gallons, 74 imperial gallons).

What is Capsize Screening Formula (CSF)?

The capsize screening value for Wasa 530 is 1.78, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.8 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Wasa 530 is about 386 kg/cm, alternatively 2162 lbs/inch.
Meaning: if you load 386 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2162 lbs cargo on the boat it will sink 1 inch.

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Wasa 530 is 31.9.

What is L/B (Length Beam Ratio)?

The l/b ratio for Wasa 530 is 3.67.

What is Displacement Length Ratio?

The DL-ratio for Wasa 530 is 179 which categorizes this boat among 'light racers'.

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 69m² (742 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

We are always looking for new photos. If you can contribute with photos for Wasa 530 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.