The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like many other boats made of mahogany. Mahogany belongs to the hardwood species, known for being water-repellent and resistant to decay. It has an attractive wood grain and holds wood polish and varnish well.
The boat is equipped with 0 cabins, 8 berths, a galley, 1500.0 liter fresh water capacity, toilet facility and 240.0 liter waste water capacity.
The boat has more than one rig.
One option is a ketch rig. A ketch rig is generally considered easier to handle, because the sails are smaller, and because it can sail on most points to the wind with one sail completely taken down for repair or while reefing. The sail configuration of a ketch allows for better comfort and stability when sailing downwind or on a broad reach.
Another option is a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Sweden Yachts 70 has been built with different keel alternatives.
Fin keel
One option is a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Sweden Yachts 70 can only enter major marinas as the draft is about 2.60 - 2.70 meter (8.53 - 8.83 ft) dependent on the load. See immersion rate below.
Wing keel
But be aware that even though a Wing Keel keel is very good for speed racing, a fishing nets and the like in the water can easily make you into a troublesome situation.
The boat may be equipped with an inboard Volvo Penta TAMD 41D diesel engine at 170 hp (126 kW). Calculated max speed is about 8.5 knots
The fuel tank has a capacity of 1200.0 liters (317 US gallons, 263 imperial gallons).
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Sweden Yachts 70 is 1.66, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
Sweden Yachts 70 holds a CE certification:
The boat is by European Union certified as Class A. OCEAN:What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 9.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Sweden Yachts 70 is about 555 kg/cm, alternatively 3109 lbs/inch.
Meaning: if you load 555 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 3109 lbs cargo on the boat it will sink 1 inch.
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Sweden Yachts 70 is 4.10.
Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 93m2 (1001 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
Masthead rig | ||||
Usage | Length | Diameter | ||
Jib sheet | 21.2 m | (69.7 feet) | 16 mm | (5/8 inch) |
Genoa sheet | 21.2 m | (69.7 feet) | 16 mm | (5/8 inch) |
Mainsheet | 53.1 m | (174.3 feet) | 16 mm | (5/8 inch) |
Spinnaker sheet | 46.8 m | (153.4 feet) | 16 mm | (5/8 inch) |
Ketch rig | ||||
Usage | Length | Diameter | ||
Jib sheet | 21.2 m | (69.7 feet) | 16 mm | (5/8 inch) |
Genoa sheet | 21.2 m | (69.7 feet) | 16 mm | (5/8 inch) |
Mainsheet | 53.1 m | (174.3 feet) | 16 mm | (5/8 inch) |
Spinnaker sheet | 46.8 m | (153.4 feet) | 16 mm | (5/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Sweden Yachts 70 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.