Review of Princess 35
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Princess 35 or similar boat for sale
The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a sandwich construction which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The interior is like most other boats made of teak. Teak has the advantage of being naturally very oily and therefore water-repellent, which is suitable on boats.
The boat is equipped with 3 cabins, 6-7 berths, a galley, 364.0 liter fresh water capacity and toilet facility.
Unknown keel type
The boat can enter even shallow marinas as the draft is just about 1.00 - 1.10 meter (3.28 - 3.58 ft) dependent on the load. See immersion rate below.
The Princess 35 has been equipped with different engine alternatives.
Alternative 1:
Princess 35 may be equipped with dual inboard Volvo Penta TAMD 41 diesel engines at 200 hp (149 kW). Max speed is 28.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 2:
The boat may be equipped with dual inboard Volvo Penta TAMD 41 diesel engines at 200 hp (149 kW).
The transmission is a Z-drive aka sterndrive.
Alternative 3:
The boat may be equipped with dual inboard Volvo Penta TAMD 40B diesel engines at 165 hp (122 kW).
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 4:
Princess 35 may be equipped with dual inboard Volvo Penta TAMD 40B diesel engines at 165 hp (122 kW).
The transmission is a Z-drive aka sterndrive.
Alternative 5:
The boat may be equipped with dual inboard Cummins 6BTA diesel engines at 250 hp (186 kW).
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank, which is made of stainless steel, has a capacity of 682.0 liters (180 US gallons, 150 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Princess 35 is about 268 kg/cm, alternatively 1504 lbs/inch.
Meaning: if you load 268 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1504 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is L/B (Length Beam Ratio)?
The l/b ratio for Princess 35 is 2.88.
Curiosities
In Denmark, you are required to have achieved a 'powerboat driving license' in order to sail a powerboat.
In this context a boat is considered a powerboat if:
Danish definition of a powerboat
Maintenance
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Princess 35 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.