Review of Morgan 32 Mk III

Basic specs.

The Morgan 32 Mk III is a sailboat designed by the Canadian maritime architect Edward S. Brewer in the early eighties. The Morgan 32 Mk III is built by the American yard Morgan Yacht Corp..

Here we would have liked to show you nice photos of the Morgan 32 Mk III.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Morgan 32 Mk III or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior

The boat is equipped with 132.0 liter fresh water capacity.

Keel

Fin keel

The Morgan 32 Mk III is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can enter most marinas as the draft is just about 1.62 - 1.72 meter (5.31 - 5.61 ft) dependent on the load. See immersion rate below.

Engine

Morgan 32 Mk III may be equipped with an inboard Yanmar diesel engine at 22 hp (16 kW). Calculated max speed is about 5.3 knots

The fuel tank has a capacity of 102.0 liters (26 US gallons, 22 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Morgan 32 Mk III is 2.07, indicating that this boat would not be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 6.7 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Morgan 32 Mk III is about 179 kg/cm, alternatively 1003 lbs/inch.
Meaning: if you load 179 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1003 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Morgan 32 Mk III is 24.0.

Comparing this ratio with similar sailboats show that it is more comfortable than 50% of all similar sailboat designs. This is an average comfort value!

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Morgan 32 Mk III is 2.78.

Compared with other similar sailboats it is more spacy than 85% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Morgan 32 Mk III is 36%.

This ballast ratio shows a righting moment that is higher than 24% of all similar sailboat designs. A righting moment (ability to resist heeling) significantly below average.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Morgan 32 Mk III is 314 which categorizes this boat among 'medium weight cruisers'.

21% of all similar sailboat designs are categorized as heavier. A heavy displacement combined with smaller water plane area has lower acceleration and is more comfortable.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 29m² (312 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	9.8 m	(32.0 feet)	12 mm	(1/2 inch)
Genoa sheet	9.8 m	(32.0 feet)	12 mm	(1/2 inch)
Mainsheet	24.4 m	(80.0 feet)	12 mm	(1/2 inch)
Spinnaker sheet	21.5 m	(70.4 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Morgan 32 Mk III it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.