YachtDatabase.com

Review of Hinrichsen 33


Hinrichsen 33
Hinrichsen 33.

Basic specs.

sail specifications
The Hinrichsen 33 is a sailboat designed by the maritime architect Herman Hinrichsen.

Looking for a new boat? Find a Hinrichsen 33 or similar boat for sale

Hull

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.


Interior

The boat is equipped with a galley, 400.0 liter fresh water capacity, toilet facility and 80.0 liter waste water capacity.


Keel

Unknown keel type

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.


Engine

Hinrichsen 33 may be equipped with an inboard Vetus Mitsubishi M4.14 engine at 33 hp (24 kW).

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 180.0 liters (47 US gallons, 39 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Hinrichsen 33 is 1.94, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Hinrichsen 33 is about 232 kg/cm, alternatively 1300 lbs/inch.
Meaning: if you load 232 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1300 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Hinrichsen 33 is 2.83.

Slim Wide 82% 0 50 100
Compared with other similar sailboats it is more spacy than 82% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 9.9 m(32.5 feet)12 mm(1/2 inch)
Genoa sheet 9.9 m(32.5 feet)12 mm(1/2 inch)
Mainsheet 24.8 m(81.2 feet)12 mm(1/2 inch)
Spinnaker sheet21.8 m(71.5 feet)12 mm(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Hinrichsen 33 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References