YachtDatabase.com

Review of Glacer 44


Basic specs.

sail specifications
The Glacer 44 is a large sailboat designed by the German maritime architect Hort E. Glacer.

Here we would have liked to show you nice photos of the Glacer 44.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Glacer 44 or similar boat for sale

Hull

The hull is made of aluminium. Aluminum is strong and forgiving. Where an impact on a fiberglass hull will result in major gelcoat damage and possible cracking, an aluminum hull will probably only have a scratch or a small bend. The only concern is electrolysis. Ensure that you have proper sacrificial anodes installed.


Interior

The boat is equipped with 7 berths.


Keel

Unknown keel type

The boat can only enter major marinas as the draft is about 1.84 - 1.94 meter (6.04 - 6.34 ft) dependent on the load. See immersion rate below.


Engine

Glacer 44 may be equipped with an inboard diesel engine

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Glacer 44 is 1.81, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Glacer 44 is about 359 kg/cm, alternatively 2013 lbs/inch.
Meaning: if you load 359 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 2013 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Glacer 44 is 3.35.

Slim Wide 54% 0 50 100
Compared with other similar sailboats it is more spacy than 54% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 16.86


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 13.4 m(44.0 feet)16 mm(5/8 inch)
Genoa sheet13.4 m(44.0 feet)16 mm(5/8 inch)
Mainsheet 33.5 m(110.1 feet)16 mm(5/8 inch)
Spinnaker sheet29.5 m(96.9 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Glacer 44 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References