Review of Farr Phase 4

Basic specs.

The Farr Phase 4 is a large sailboat designed by the maritime architect Bruce Farr in the late eighties. The Farr Phase 4 is built by the Australian yard Binks Yacht Contructions.

Here we would have liked to show you nice photos of the Farr Phase 4.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Farr Phase 4 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Interior

The boat is equipped with 681.0 liter fresh water capacity.

Rig

The Farr Phase 4 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

Fin keel

The Farr Phase 4 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The boat can enter most marinas as the draft is just about 1.70 - 1.80 meter (5.58 - 5.88 ft) dependent on the load. See immersion rate below.

Engine

Farr Phase 4 may be equipped with an inboard Volvo Penta diesel engine

The fuel tank has a capacity of 189.0 liters (49 US gallons, 41 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Farr Phase 4 is 2.10, indicating that this boat would not be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 7.6 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Farr Phase 4 is about 249 kg/cm, alternatively 1394 lbs/inch.
Meaning: if you load 249 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1394 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Farr Phase 4 is 20.3.

Comparing this ratio with similar sailboats show that it is more comfortable than 14% of all similar sailboat designs. This is a comfort value significantly below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Farr Phase 4 is 3.18.

Compared with other similar sailboats it is more spacy than 62% of all other designs. It seems that the designer has chosen a slightly more spacy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Farr Phase 4 is 171 which categorizes this boat among 'light racers'.

82% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

What is SA/D (Sail Area Displacement ratio)?

The SA/D for Farr Phase 4 with ISO 8666 reference sail is 18.3, with a 135% genua the SA/D is 21.6.

The SA/D ratio indicates that it is faster than 62% of all similar sailboat designs in light wind.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 40m² (430 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

Dimensions of sail for masthead rig.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	32.4 m	(106.4 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	32.4 m	(106.4 feet)	12 mm	(1/2 inch)
Spinnaker halyard	32.4 m	(106.4 feet)	12 mm	(1/2 inch)
Jib sheet	12.0 m	(39.4 feet)	14 mm	(0.55 inch)
Genoa sheet	12.0 m	(39.4 feet)	14 mm	(0.55 inch)
Mainsheet	30.0 m	(98.4 feet)	14 mm	(0.55 inch)
Spinnaker sheet	26.4 m	(86.6 feet)	14 mm	(0.55 inch)
Cunningham	4.7 m	(15.4 feet)	12 mm	(1/2 inch)
Kickingstrap	9.4 m	(30.8 feet)	12 mm	(1/2 inch)
Clew-outhaul	9.4 m	(30.8 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Farr Phase 4 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.