Review of Concorde 38 De Luxe
Basic specs.
Looking for a new boat? Find a Concorde 38 De Luxe or similar boat for sale
The hull is made of hand laid fibreglass while the deck is made of fibreglass. Generally, a hull made of hand laid fibreglass requires only a minimum of maintenance during the sailing season.
The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.
The deck is a double deck which improves the indoor climate.
The boat is equipped with 3 cabins, 6-8 berths, a galley, 125.0 liter fresh water capacity and toilet facility.
Note: the boat has also been sold to be self-made/-interiored, which means that the quality of each boat may vary.
The Concorde 38 De Luxe is equipped with a fractional rig. A fractional rig has smaller headsails which make tacking easier, which is an advantage for cruisers and racers, of course. The downside is that having the wind from behind often requires a gennaker or a spinnaker for optimal speed.
Fin keel
The Concorde 38 De Luxe is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
Concorde 38 De Luxe can only enter major marinas as the draft is about 1.87 - 1.97 meter (6.14 - 6.44 ft) dependent on the load. See immersion rate below.
The Concorde 38 De Luxe has been equipped with different engine alternatives.
Alternative 1:
The boat may be equipped with an inboard Solé engine at 23 hp (17 kW). The speed is 8.0 knots.
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Alternative 2:
The boat may be equipped with an inboard Bukh diesel engine
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
The fuel tank has a capacity of 50.0 liters (13 US gallons, 10 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Concorde 38 De Luxe is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Concorde 38 De Luxe is about 182 kg/cm, alternatively 1023 lbs/inch.
Meaning: if you load 182 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1023 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Concorde 38 De Luxe is 25.5 - 26.5.
What is L/B (Length Beam Ratio)?
The l/b ratio for Concorde 38 De Luxe is 3.94.
The ballast ratio for Concorde 38 De Luxe is 39%.
What is Displacement Length Ratio?
The DL-ratio for Concorde 38 De Luxe is 174 which categorizes this boat among 'light racers'.
What is Relative Speed Performance?
The Relative Speed Performance for Concorde 38 De Luxe is 50
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 34m2 (365 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Jib sheet | 11.5 m | (37.7 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 11.5 m | (37.7 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 28.8 m | (94.3 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 25.3 m | (83.0 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Concorde 38 De Luxe it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.