Review of Bénéteau Antares 9.80

Basic specs.

The Bénéteau Antares 9.80 is a motorboat. The Bénéteau Antares 9.80 is built by the French yard Bénéteau.

Here we would have liked to show you nice photos of the Bénéteau Antares 9.80.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Bénéteau Antares 9.80 or similar boat for sale

Hull

Both the hull and the deck is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.

Interior

The boat is equipped with one cabin, 3 berths, a galley, 220.0 liter fresh water capacity and toilet facility.

Engine

The boat may be equipped with dual inboard Volvo Penta D4 diesel engines at 450 hp (335 kW).

The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.

The fuel tank has a capacity of 790.0 liters (208 US gallons, 173 imperial gallons).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

EU classification

Bénéteau Antares 9.80 holds two CE certifications:

If less than 8 in on board the boat is by European Union certified as Class B. OFFSHORE:

Designed for offshore voyages where conditions up to, and including, wind force 8 (Beaufort scale) and significant wave heights up to, and including, 4 m may be experienced.

If less than 10 in on board the boat is by European Union certified as Class C. INSHORE:

Designed for voyages in coastal waters, large bays, estuaries, lakes and rivers where conditions up to, and including, wind force 6 (Beaufort scale) and significant wave heights up to, and including, 2 m may be experienced.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Bénéteau Antares 9.80 is about 223 kg/cm, alternatively 1254 lbs/inch.
Meaning: if you load 223 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1254 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Bénéteau Antares 9.80 is 2.85.

Compared with other similar motor boats it is more spacy than 79% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Curiosities

Powerboat?

In Denmark, you are required to have achieved a 'powerboat driving license' in order to sail a powerboat.
In this context a boat is considered a powerboat if:

Danish definition of a powerboat

According to this definition this boat is categorized as a Powerboat.

Maintenance

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Antarès 9.80 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.