Review of Mistress 32
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Mistress 32 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.
The Mistress 32 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.
The Mistress 32 has been built with different keel alternatives.
Fin keel
One option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of iron. Many people prefer lead keel in favour of iron. The main argument is that lead is much heavier than iron and a lead keel can therefore be made smaller which again result in less wet surface, i.e. less drag. In fact iron is quite heavy, just 30% less heavy than lead, so the advantage of a lead keel is often overstated. As the surface of a fin type keel is just a fraction of the total wet surface, the difference between an iron keel and a lead keel can in reality be ignored for cruising yachts.
The boat can enter most marinas as the draft is just about 1.65 - 1.75 meter (5.41 - 5.71 ft) dependent on the load. See immersion rate below.
Fin keel
Another option is a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 1.85 - 1.95 meter (6.07 - 6.37 ft) dependent on the load. See immersion rate below.
The Mistress 32 has been equipped with different engine alternatives.
Alternative 1:
Mistress 32 may be equipped with an inboard Volvo Penta MD1B diesel engine
Alternative 2:
The boat may be equipped with an inboard engine
The transmission is a shaft drive. A shaft drive will in the long run require less maintenance than other types of drive e.g. a sail drive.
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Mistress 32 is 1.89, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 6.4 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Mistress 32 is about 131 kg/cm, alternatively 735 lbs/inch.
Meaning: if you load 131 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 735 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Mistress 32 is 23.9.
What is L/B (Length Beam Ratio)?
The l/b ratio for Mistress 32 is 3.42.
The ballast ratio for Mistress 32 is 43%.
What is Displacement Length Ratio?
The DL-ratio for Mistress 32 is 296 which categorizes this boat among 'medium weight cruisers'.
What is Relative Speed Performance?
The Relative Speed Performance for Mistress 32 is 24
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 23m2 (247 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
Dimensions of sail for masthead rig.
Are your sails worn out? You might find your next sail here: Sails for Sale
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
| Mainsail halyard | 4.0 m | (13.0 feet) | 10 mm | (3/8 inch) |
| Jib/genoa halyard | 4.0 m | (13.0 feet) | 10 mm | (3/8 inch) |
| Spinnaker halyard | 4.0 m | (13.0 feet) | 10 mm | (3/8 inch) |
| Jib sheet | 9.7 m | (31.8 feet) | 12 mm | (1/2 inch) |
| Genoa sheet | 9.7 m | (31.8 feet) | 12 mm | (1/2 inch) |
| Mainsheet | 24.2 m | (79.6 feet) | 12 mm | (1/2 inch) |
| Spinnaker sheet | 21.3 m | (70.0 feet) | 12 mm | (1/2 inch) |
| Cunningham | 1.1 m | (3.5 feet) | 10 mm | (3/8 inch) |
| Kickingstrap | 2.1 m | (7.0 feet) | 10 mm | (3/8 inch) |
| Clew-outhaul | 2.1 m | (7.0 feet) | 10 mm | (3/8 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Mistress 32 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.