Review of Carter 37

Basic specs.

The Carter 37 is a sailboat designed by the British maritime architect Richard Carter. The Carter 37 is built by the Greek yard Olympic Yachts.

Here we would have liked to show you nice photos of the Carter 37.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Carter 37 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.

Keel

Unknown keel type

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 1.92 - 2.02 meter (6.30 - 6.60 ft) dependent on the load. See immersion rate below.

Engine

The boat is typically equipped with an inboard Perkins diesel engine at 50 hp (37 kW).

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Carter 37 is about 281 kg/cm, alternatively 1575 lbs/inch.
Meaning: if you load 281 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1575 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Carter 37 is 3.00.

Compared with other similar sailboats it is more spacy than 76% of all other designs. It seems that the designer has chosen a significantly more spacy hull design.

Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Carter 37 is 41%.

This ballast ratio shows a righting moment that is higher than 58% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.

Over- / underrigged

The Carter 37 has more rig than 46% of all similar sailboats, which indicates that the boat is slightly underrigged.

Maintenance

Rig

Dimensions of sail.

Are your sails worn out? You might find your next sail here: Sails for Sale

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Mainsail halyard	33.7 m	(110.5 feet)	12 mm	(1/2 inch)
Jib/genoa halyard	33.7 m	(110.5 feet)	12 mm	(1/2 inch)
Spinnaker halyard	33.7 m	(110.5 feet)	12 mm	(1/2 inch)
Jib sheet	11.2 m	(36.8 feet)	14 mm	(0.55 inch)
Genoa sheet	11.2 m	(36.8 feet)	14 mm	(0.55 inch)
Mainsheet	28.1 m	(92.1 feet)	14 mm	(0.55 inch)
Spinnaker sheet	24.7 m	(81.1 feet)	14 mm	(0.55 inch)
Cunningham	3.5 m	(11.6 feet)	12 mm	(1/2 inch)
Kickingstrap	7.1 m	(23.2 feet)	12 mm	(1/2 inch)
Clew-outhaul	7.1 m	(23.2 feet)	12 mm	(1/2 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Carter 37 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.