Review of Sydney 46

Basic specs.

The Sydney 46 is a large sailboat designed by the maritime architect Murray Burns Dovell in the late nineties. The Sydney 46 is built by the Australian yard Bashford International.

Here we would have liked to show you nice photos of the Sydney 46.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find a Sydney 46 or similar boat for sale

Hull

The hull is a double hull which improves the indoor climate. Especially when the water is colder than the air in the cabin, then the double hull insulates against cold water and reduce the condense water in the cabin.

Rig

The Sydney 46 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.

Keel

Fin keel

The Sydney 46 is equipped with a fin keel. A boat with a fin keel is more manoeuvrable but has less directional stability than a similar boat with a full keel.

The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.

The boat can only enter major marinas as the draft is about 2.88 - 2.98 meter (9.45 - 9.75 ft) dependent on the load. See immersion rate below.

Engine

The boat may be equipped with an inboard Yanmar 3JH diesel engine at 48 hp (35 kW). Calculated max speed is about 7.4 knots

Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Sydney 46 is 2.05, indicating that this boat would not be accepted to participate in ocean races.

Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 8.3 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.

Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Sydney 46 is about 318 kg/cm, alternatively 1781 lbs/inch.
Meaning: if you load 318 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 1781 lbs cargo on the boat it will sink 1 inch.

Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

Motion Comfort Ratio

What is Motion Comfort Ratio (MCR)?

The Motion Comfort Ratio for Sydney 46 is 21.6.

Comparing this ratio with similar sailboats show that it is more comfortable than 12% of all similar sailboat designs. This is a comfort value significantly below average.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Sydney 46 is 3.46.

Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.

D/L (Displacement Length Ratio)

What is Displacement Length Ratio?

The DL-ratio for Sydney 46 is 148 which categorizes this boat among 'ultra light racers'.

82% of all similar sailboat designs are categorized as heavier. A light displacement requires less sailarea and has higher accellerations.

SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 26.14

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 61m² (656 ft²).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.

**Guiding dimensions of running rig**
Usage	Length		Diameter
Jib sheet	14.2 m	(46.6 feet)	16 mm	(5/8 inch)
Genoa sheet	14.2 m	(46.6 feet)	16 mm	(5/8 inch)
Mainsheet	35.5 m	(116.5 feet)	16 mm	(5/8 inch)
Spinnaker sheet	31.2 m	(102.5 feet)	16 mm	(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.

Finally

We are always looking for new photos. If you can contribute with photos for Sydney 46 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.

References

[Ref 1]: ISO 8666 Small craft — Principal data.
[Ref 3]: ISO 12215-5 Small craft — Hull construction and scantlings.