YachtDatabase.com

Review of Oyster 625


Basic specs.

sail specifications
The Oyster 625 is a large sailboat designed by the British maritime architect Robert Humphreys in the early 2010.

Here we would have liked to show you nice photos of the Oyster 625.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Oyster 625 or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.


Interior

The boat is equipped with 8 berths and 1200.0 liter fresh water capacity.


Rig

The Oyster 625 is equipped with a masthead rig. The advantage of a masthead rig is its simplicity and the fact that a given sail area - compared with a fractional rig - can be carried lower and thus with less heeling moment.


Keel

The Oyster 625 has been built with different keel alternatives.

Unknown keel type

The boat can only enter major marinas as the draft is about 2.80 - 2.90 meter (9.19 - 9.49 ft) dependent on the load. See immersion rate below.

Unknown keel type

Oyster 625 can only enter major marinas as the draft is about 2.15 - 2.25 meter (7.05 - 7.35 ft) dependent on the load. See immersion rate below.

CentreBoard

The Oyster 625 is equipped with a centreboard keel. A centreboard keel is a pivoting lifting keel, allowing to sail both coastal and inland waters.

The boat can only enter major marinas as the draft is about 1.82 - 1.92 meter (5.97 - 6.27 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with an inboard Volvo Penta D4-180 diesel engine at 180 hp (134 kW). Calculated max speed is about 8.7 knots

The fuel tank has a capacity of 1700.0 liters (449 US gallons, 373 imperial gallons).


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Oyster 625 is 1.70, indicating that this boat could - if evaluated by this formula alone - be accepted to participate in ocean races.


Theoretical Maximum Hull Speed

What is Theoretical Maximum Hull Speed?

The theoretical maximal speed of a displacement boat of this length is 10.1 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Oyster 625 is about 628 kg/cm, alternatively 3518 lbs/inch.
Meaning: if you load 628 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 3518 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Oyster 625 is 3.50.


SA/D (Sail Area Displacement ratio)

SA/D (Sail Area Displacement ratio)
Indicates how fast the boat is in light wind:
- Cruising Boats have ratios 10-15
- Cruiser-Racers have ratios 16-20
- Racers have ratios above 20
- High-Performance Racers have ratios above 24
Sail-area/displacement ratio (SA/D ratio): 23.08


Sorry, we do not have sufficient statistical information available for this boat to provide a significant reliable analysis.

Maintenance

Bottom Paint

When buying anti-fouling bottom paint, it's nice to know how much to buy. The surface of the wet bottom is about 107m2 (1151 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.

Note: If you use a paint roller you will need more paint than if you use a paintbrush.


Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 19.0 m(62.4 feet)16 mm(5/8 inch)
Genoa sheet19.0 m(62.4 feet)16 mm(5/8 inch)
Mainsheet 47.6 m(156.1 feet)16 mm(5/8 inch)
Spinnaker sheet41.9 m(137.4 feet)16 mm(5/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Oyster 625 it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References