YachtDatabase.com

Review of Offshore 1/4 ton


Basic specs.

sail specifications
The Offshore 1/4 ton is a small sailboat designed by the maritime architect Bernard Olesinski in the early seventies.

Here we would have liked to show you nice photos of the Offshore 1/4 ton.
If you have a photo you would like to share: Upload Image

Looking for a new boat? Find an Offshore 1/4 ton or similar boat for sale

Hull

The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season. And outside the sailing season, just bottom cleaning and perhaps anti-fouling painting once a year - a few hours of work, that's all.


Interior

The interior is like few other boats made in fibreglass.


Keel

Fin keel

The Offshore 1/4 ton is equipped with a fin keel. The fin keel is the most common keel and provides splendid manoeuvrability. The downside is that it has less directional stability than a long keel.

The boat can enter even shallow marinas as the draft is just about 1.37 - 1.47 meter (4.49 - 4.79 ft) dependent on the load. See immersion rate below.


Engine

The boat may be equipped with a Petter diesel engine at 5 hp (3 kW)..


Sailing characteristics

This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.

Stability and Safety

What is Capsize Screening Formula (CSF)?

The capsize screening value for Offshore 1/4 ton is 2.27, indicating that this boat would not be accepted to participate in ocean races.


Immersion rate

The immersion rate is defined as the weight required to sink the boat a certain level. The immersion rate for Offshore 1/4 ton is about 125 kg/cm, alternatively 700 lbs/inch.
Meaning: if you load 125 kg cargo on the boat then it will sink 1 cm. Alternatively, if you load 700 lbs cargo on the boat it will sink 1 inch.


Sailing statistics

This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.

L/B (Length Beam Ratio)

What is L/B (Length Beam Ratio)?

The l/b ratio for Offshore 1/4 ton is 2.99.

Wide Slim 54% 0 50 100
Compared with other similar sailboats it is slimmer than 54% of all other designs. It seems that the designer has chosen a slightly more speedy hull design.


Ballast Ratio

What is a Ballast Ratio?

The ballast ratio for Offshore 1/4 ton is 42%.

Low High 62% 0 50 100
This ballast ratio shows a righting moment that is higher than 62% of all similar sailboat designs. A righting moment (ability to resist heeling) just above average.


Maintenance

Rig

If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.



Guiding dimensions of running rig
UsageLengthDiameter
Jib sheet 7.5 m(24.5 feet)10 mm(3/8 inch)
Genoa sheet 7.5 m(24.5 feet)10 mm(3/8 inch)
Mainsheet 18.7 m(61.3 feet)10 mm(3/8 inch)
Spinnaker sheet16.4 m(53.9 feet)10 mm(3/8 inch)

Boat owner's ideas

This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.

Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.



Finally

We are always looking for new photos. If you can contribute with photos for Offshore 1/4 ton it would be a great help.

If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.



References