Review of Humphreys One Design 35
Basic specs.
If you have a photo you would like to share: Upload Image
Looking for a new boat? Find a Humphreys One Design 35 or similar boat for sale
The hull is made of fibreglass. Generally, a hull made of fibreglass requires only a minimum of maintenance during the sailing season.
The boat is equipped with 151.0 liter fresh water capacity.
Unknown keel type
The keel is made of lead. Compared with iron, lead has the advantage of being 44% heavier, which allows a smaller keel and hence less water resistance and higher speed.
The boat can only enter major marinas as the draft is about 2.16 - 2.26 meter (7.09 - 7.39 ft) dependent on the load. See immersion rate below.
Humphreys One Design 35 may be equipped with an inboard Volvo Penta MD2020 diesel engine at 19 hp (14 kW). Calculated max speed is about 5.9 knots
The fuel tank has a capacity of 79.0 liters (20 US gallons, 17 imperial gallons).
Sailing characteristics
This section covers widely used rules of thumb to describe the sailing characteristics. Please note that even though the calculations are correct, the interpretation of the results might not be valid for extreme boats.
What is Capsize Screening Formula (CSF)?
The capsize screening value for Humphreys One Design 35 is 2.12, indicating that this boat would not be accepted to participate in ocean races.
What is Theoretical Maximum Hull Speed?
The theoretical maximal speed of a displacement boat of this length is 7.5 knots. The term "Theoretical Maximum Hull Speed" is widely used even though a boat can sail faster. The term shall be interpreted as above the theoretical speed a great additional power is necessary for a small gain in speed.
The immersion rate is defined as the weight required to sink the boat a certain level.
The immersion rate for Humphreys One Design 35 is about 217 kg/cm, alternatively 1218 lbs/inch.
Meaning: if you load 217 kg cargo on the boat then it will sink 1 cm.
Alternatively, if you load 1218 lbs cargo on the boat it will sink 1 inch.
Sailing statistics
This section is statistical comparison with similar boats of the same category. The basis of the following statistical computations is our unique database with more than 26,000 different boat types and 350,000 data points.
What is Motion Comfort Ratio (MCR)?
The Motion Comfort Ratio for Humphreys One Design 35 is 18.1.
What is L/B (Length Beam Ratio)?
The l/b ratio for Humphreys One Design 35 is 3.11.
The ballast ratio for Humphreys One Design 35 is 43%.
What is Displacement Length Ratio?
The DL-ratio for Humphreys One Design 35 is 140 which categorizes this boat among 'ultra light racers'.
Maintenance
When buying anti-fouling bottom paint, it's nice to know how much to buy.
The surface of the wet bottom is about 40m2 (430 ft2).
Based on this, your favourite maritime shop can tell you the quantity you need.
Note: If you use a paint roller you will need more paint than if you use a paintbrush.
If you need to renew parts of your running rig and is not quite sure of the dimensions, you may find the estimates computed below useful.
| Usage | Length | Diameter | ||
|---|---|---|---|---|
| Jib sheet | 10.6 m | (34.9 feet) | 14 mm | (0.55 inch) |
| Genoa sheet | 10.6 m | (34.9 feet) | 14 mm | (0.55 inch) |
| Mainsheet | 26.6 m | (87.2 feet) | 14 mm | (0.55 inch) |
| Spinnaker sheet | 23.4 m | (76.7 feet) | 14 mm | (0.55 inch) |
This section is reserved boat owner's modifications, improvements, etc. Here you might find (or contribute with) inspiration for your boat.
Do you have changes/improvements you would like to share? Upload a photo and describe what you have done.
We are always looking for new photos. If you can contribute with photos for Humphreys One Design 35 it would be a great help.
If you have any comments to the review, improvement suggestions, or the like, feel free to contact us. Criticism helps us to improve.